I am not selling this, But providing information to the interested persons of these options they can do themselves or pay for someone to do.
If you are stuck on baseband 5.14.02, 5.15.04 or 5.16.02 which presently cannot be unlocked by ultrasn0w, you can fix it by replacing the baseband chip. Fix your GPS issue if you have baseband 6.15.00 and increase the resale value of your phone with a baseband that can be unlocked with ultrasn0w.
This is a genuine Infineon X-Gold 608 baseband chip which is designed for iPhone 3G, 3GS and iPad 1 (FYI – that’s why iPad’s baseband 6.15.00 can be implanted into the iPhone).
To learn more about this microchip, the full technical specifications can be downloaded from here.
The baseband chip is pre-programmed with baseband version 5.13.04 which can be unlocked using ultrasn0w.
What’s the Cost?
=x=x=x=x=x=x=x=x=x=x=x=x=x=x=
What you need:
Steps:
1. Disassemble your iPhone and remove the logic board. See Google video here.
2. Remove the EMI shield and take note of the baseband chip marked ‘X.’
3. Cover the surrounding area of the mainboard and use a hot air gun to melt the solder that holds the chip. Ideally, the temperature should be around 290 degree C. Check out some YouTube videos here.
4. Gently remove the baseband chip from the logic board.
5. Clean up any residue left on the logic board with a soldering gun and rub the area with a piece of cotton dabbed with alcohol.
6. A close-up view of the cleaned area of the logic board.
7. Now you are ready to mount the new baseband chip. See YouTube video here for recommended ways to do it.
8. Once you have mounted the chip, wait for at least half an hour before reassembling your iPhone.
9. Turn on your iPhone and check that you now have an older baseband 5.13.04.
10. Jailbreak your iPhone if you haven’t done so and unlock it with ultrasn0w. You now have an unlocked iPhone and your GPS and other issues should be resolved.
Note: This method does not make your iPhone factory-unlocked. You still have to be careful not to update it directly via iTunes.
If you are stuck on baseband 5.14.02, 5.15.04 or 5.16.02 which presently cannot be unlocked by ultrasn0w, you can fix it by replacing the baseband chip. Fix your GPS issue if you have baseband 6.15.00 and increase the resale value of your phone with a baseband that can be unlocked with ultrasn0w.
This is a genuine Infineon X-Gold 608 baseband chip which is designed for iPhone 3G, 3GS and iPad 1 (FYI – that’s why iPad’s baseband 6.15.00 can be implanted into the iPhone).
To learn more about this microchip, the full technical specifications can be downloaded from here.
The baseband chip is pre-programmed with baseband version 5.13.04 which can be unlocked using ultrasn0w.
What’s the Cost?
- Baseband chip: pre-programmed with baseband 5.13.04 or lower that can be unlocked with ultrasn0w $ 57.95 (September Promo – extended to October, now to November due to popular demand!)
- Labor: USD23.00
- Express Shipping: USD25.00 to Australia, NZ, North America and Western European destinations.
- Standard Shipping: USD8.00 to any destination (trackable online via http://www.track-trace.com/post).
=x=x=x=x=x=x=x=x=x=x=x=x=x=x=
Exclusive: How to Replace iPhone 3G/3GS Baseband Chip Step-by-Step Guide with Photos
If you are familiar with DIY electronics repairs and do not mind destroying your iPhone, you can refer to the rough guide below on how to replace your baseband chip pre-programmed with baseband 5.13.04 (or lower) which can be unlocked using ultrasn0w 1.2. This method will fix your iPhone’s GPS issue (baseband 6.15.00).What you need:
- Hot air gun
- Solder paste
- Soldering iron
- Tweezers
- Isopropyl alcohol
- Pre-programmed replacement baseband chip (you can purchase this from us)
- Good lighting, table etc.
- Patience
Steps:
1. Disassemble your iPhone and remove the logic board. See Google video here.
2. Remove the EMI shield and take note of the baseband chip marked ‘X.’
5. Clean up any residue left on the logic board with a soldering gun and rub the area with a piece of cotton dabbed with alcohol.
6. A close-up view of the cleaned area of the logic board.
7. Now you are ready to mount the new baseband chip. See YouTube video here for recommended ways to do it.
8. Once you have mounted the chip, wait for at least half an hour before reassembling your iPhone.
9. Turn on your iPhone and check that you now have an older baseband 5.13.04.
10. Jailbreak your iPhone if you haven’t done so and unlock it with ultrasn0w. You now have an unlocked iPhone and your GPS and other issues should be resolved.
Note: This method does not make your iPhone factory-unlocked. You still have to be careful not to update it directly via iTunes.
No comments:
Post a Comment